Ultrak JPD-100 Bedienungsanleitung

Issue 1, Rev. E – January 2001JPD-101USER’S MANUALMANUAL NUMBER 518007-3960Ultrak®, Inc.4465 Coonpath RoadCarroll, OH 43112(800) 443-6680•(740) 756-9

ivTABLE OF CONTENTSPageC.2.2.1 CATS Video Switcher Rear Panel Installation ... C-4C.2.2.2 CATS Video Switcher Front P

4-4a. 8-Pin Telephone Jack ConnectorA coiled cable assembly (P/N 849518-0306) is provided with thecontroller for connection from the 8-Pin telephone j

4-5b. 5-Pin DIN ConnectorA 101 key enhanced KBD-100 keyboard is required for programmingSmartScan units. Plug the keyboard cable into the 5-pin DINco

4-64.3.1 Stand-Alone Controller Installation.When used as a stand-alone unit, the controller requires a DIA-01,DIA-01/X or DIA-01/R Control Interface

Figure 4-2. JPD-101 CONTROLLER AS A STAND-ALONE UNIT4-7

4-84.3.2 One Controller And CATS Video Switcher Installation.Make sure the controller is configured as master and communication isdisabled. Jumpers W

Figure 4-3. TYPICAL INTERCONNECT WITH JPD-101 SMART HAND CONTROLLER AND CATS VIDEO SWITCHER4-9

4-104.3.2.2 JPD-101 Connected to Rear Panel of CATS Video Switcher.To connect the controller to the rear panel COMM connector, a DIA-01Control Interfa

Figure 4-4. JPD-101 CONTROLLER W/CATS VIDEO SWITCHER (REAR PANEL CONNECTOR)4-11

4-124.3.3 Two Controllers Linked Together Installation.When linking two controllers together, two DIA-02 Control Interface Adaptersare required. Refe

Figure 4-5. TWO JPD-101 CONTROLLERS LINKED TOGETHER4-13

vLIST OF TABLESPageTable 2-1. CONTROL COMMANDS...2-58Table 4-1. MASTER/SLAVE

4-143. Using RS-422 1-twisted pair shielded cable (P/N 849518-0334),connect the transmit terminals on the DATA IN side of the DIA-02connected to the m

Figure 4-6. TWO CONTROLLERS LINKED TOGETHER W/CATS VIDEO SWITCHER (FRONT PANEL CONNECTOR)4-15

4-16Make sure one unit is configured as a master and one as a slave.Make sure communication is enabled on both units.Master Unit = Jumper W8 OUTSlave

4-174. The COMM connector on the rear panel of the CATS VideoSwitcher has 4 output ports for connection to theFastScan/SmartScan units. Refer to the

Figure 4-7. TWO CONTROLLERS LINKED TOGETHER W/CATS VIDEO SWITCHER (REAR COMM CONNECTOR)4-18

4-192. Plug the slave controller into the DATA IN on one of the DIA-02's.Plug the master controller into the DATA IN on the other DIA-02.3. Using

FARNEOPENCLOSE

viThis page left blank intentionally.

5-1SECTION 5. MAINTENANCE5.1 MAINTENANCE PROCEDURESa. Preventive MaintenanceUse of preventive maintenance allows detection and correction of minorfau

5-2Because this unit is just one part of an overall system, it may be necessaryto verify that the other equipment types have been installed and areope

5-35.2 RETURNING EQUIPMENT TO ULTRAKAny equipment returned to Ultrak for warranty or service repair must have a priorwritten Authorization to Return M

5-4This page left blank intentionally.

A-1APPENDIX A. REFERENCE MATERIALSA.1 USER'S MANUAL INDEXThe following user's manuals are for equipment associated with the JPD-101 orJPD-1

A-2FastScan and FastScan Pro II Installation(15” Single Board 517955-1030) 518427-2960SmartScan IIIB Operation and Programming 518116-2960SmartScan II

B-1APPENDIX B. QUICK REFERENCE GUIDEJPD-101 CONTROLLERFASTSCAN®/SMARTSCAN® MANUAL CONTROLFUNCTION PROCEDURE(Keystrokes are separated by a “>“)Sele

B-2AUXILIARY CONTROL(Control Camera)FUNCTION PROCEDURE(Keystrokes are separated by a “>“)Auxiliaries at Control Camera (Camera1 = CATS Video Switch

B-3PROGRAMMING THE EIGHT FUNCTION KEYSAll Keystrokes are performed on the JPD-101 Keypads.FUNCTION DEFINITION PROCEDURE(Keystrokes are separated by a

1-1SECTION 1. INTRODUCTION1.1 DESCRIPTIONThe JPD-101 Joystick Controller is an operator interface device designed toremotely control FastScan pan and

B-4PROGRAMMING THE EIGHT FUNCTION KEYS (CONT)All Keystrokes are performed on the JPD-101 Keypads.FUNCTION DEFINITION PROCEDURE(Keystrokes are separate

B-5PROGRAMMING THE EIGHT FUNCTION KEYS (CONT)All Keystrokes are performed on the JPD-101 Keypads.Modify a FunctionKey (Cont)Delete a StepPRGM> 1>

B-6This page left blank intentionally.

C-1APPENDIX C. INSTALLATION JPD-101/R RACK MOUNT JOYSTICKCONTROLLERC.1 DESCRIPTIONThe JPD-101/R Joystick Controller is designed for use in a system t

C-2C.2.1 Stand-Alone Controller.If the JPD-101/R Controller is used as a stand-alone controller, perform thefollowing steps for installation.1. The su

C-3Figure C-1. JPD-101/R AS A STAND-ALONE CONTROLLER

C-4C.2.2 CATS Video SwitcherThe JPD-101/R Controller can be connected to the front panel controllerconnector or the rear panel COMM connector on the C

C-5Figure C-2. JPD-101/R CONNECTED TO THE COMM CONNECTOR OF THE CATSVIDEO SWITCHER

C-6C.2.2.2 CATS Video Switcher Front Panel InstallationPerform the following procedures to connect the JPD-101/R Controller tothe front panel controll

C-7Figure C-3. JPD-101/R CONTROLLER CONNECTED TO THE FRONT PANEL ONTHE CATS VIDEO SWITCHER

1-2• Manual Control (pan, tilt, zoom, focus, and iris) of FastScan or SmartScandomes. Lens iris manual control requires MIO-100 auto iris override op

C-8C.3 INSTALLATION DRAWINGThe following installation drawing is provided.Title Drawing NumberPageJPD-101/R Joystick Controller UnitInstallation 70038

C-10

C-12This page left blank intentionally.

Index-1INDEXAuto-pivot, 2-2Auxiliary, 1-2, 2-8, 2-42, 2-43, 2-44,2-45, 3-5, 3-8, B-2, B-4Off, 2-43On, 2-42Azimuth displayOff, 2-57Azimuth DisplayOn, 2

Index-2PreShot, 1-2, 2-7, 2-8, 2-12, 2-20, 2-25,2-28, 2-29, 2-36, 2-37, 2-47, 2-54,3-1, 3-3, 3-5, 3-6, 3-7, 3-9, B-1, B-3Go to PreShot, 2-28List, 2-27

1-3The JPD-101 Controllers have eight programmable function (quick keys). Thefunction keys are programmed using the two 12-key keypads and the smallj

1-42. JPD-101 with a CATS Video SwitcherWhen the JPD-101 Controller is installed with a CATS Video Switcher, thecontroller can be plugged into the fro

1-54. Two JPD-101 Controllers linked together with a CATS Video SwitcherTwo JPD-101 Controllers can be linked together using two DIA-02 ControlInterfa

1-6This page left blank intentionally.

2-1SECTION 2. OPERATION2.1 CONTROLS AND INDICATORS2.1.1 Top Panel Controls and Indicators.Figure 2-1. CONTROLS AND INDICATORS, TOP PANEL

WARNINGNOT FOR OUTDOOR USE.TO REDUCE A RISK OF FIRE OR ELECTRIC SHOCK, DO NOTEXPOSE THIS PRODUCT TO RAIN OR MOISTURE.WARNINGTHIS IS A CLASS A PRODUCT.

LARGE JOYSTICK OPERATION2-21 LARGE JOYSTICKThe large joystick controls the pan, tilt, and zoom functions of aFastscan/Smartscan unit. The joystick co

SMALL JOYSTICK OPERATION2-3PASS FunctionIf the PASS function is enabled in the SmartScan unit, the pan and tilt speedrange is a function of the lens z

SMALL JOYSTICK OPERATION2-4MANUAL IRIS CONTROLSTEP 1Press the IRIS key on the function keypad and then the 2 key on the numerickeypad.IRIS 2When manua

SMALL JOYSTICK OPERATION2-5AUTOMATIC IRISThe operator can change back to automatic iris anytime while controllingthe camera.STEP 1Press the IRIS key o

SMALL JOYSTICK OPERATION2-6PROGRAMMING MODEWhen the function key programming mode (PRGM>1) is accessed, the smalljoystick becomes a programming too

LCD DISPLAYNUMERIC KEYPAD2-73 LCD DISPLAYThe display is a 2X20 EL back light super twist LCD. The viewing angle of thedisplay may be changed by turni

FUNCTION KEYPAD2-85 FUNCTION KEYPADThe function keypad is used in conjunction with the numeric keypad to carry outthe control functions of the FastSca

FUNCTION KEYS 1-82-96 FUNCTION KEYS 1-8Function keys 1 through 8 are programmable using the two 12-key keypads andthe small joystick. These keys can

2-102.1.2 Rear Panel Controls and Indicators.Figure 2-2. CONTROLS AND INDICATORS, REAR PANEL7 VIEWING ANGLE ADJUSTMENTThis screwdriver adjustment is

2-112.2 OPERATIONCAUTIONBefore Powering-Up The System, MakeSure The Programming Keyboard IsPlugged Into The JPD-101 Controller. If TheKeyboard Is Plu

DECLARATION OF CONFORMITYTo The European Community Council Directive 89/336/EECISSUED BY: Ultrak®, Inc.4465 Coonpath Road NWCarroll, OH 43112USATel:

2-12Operation of a master unit and a slave unit are exactly the same. The onlydifference is the communication path. The slave controller sends its c

LCD LANGUAGE2-132.2.1 LCD Display Language SelectionUpon power-up of the controller, the second line of the LCD display showsthe firmware and revision

SET ADDRESS IN KD6 Z-SERIES2-142.2.2 Setting the Address in the KD6 Z-Series DomeTo set the address of a KD6 Z-Series Dome, you must know the serialnu

PRIMARY CONTROL CAMERA2-152.2.3 Primary Control Camera and Control Monitor.Upon power-up of the system, the primary control camera and monitor arecame

PRIMARY CONTROL CAMERA2-16Camera #>ENTER # ENTERorCamera#>CNTL # CNTLThe controller sends a command to the switcher to switch the selectedcamera

PRIMARY CONTROL CAMERA2-17Example:The display on the controller shows CAM 1 and MON 1.CNTL - CAM 1 MON 1Enter the following command sequence to change

PRIMARY CONTROL MONITOR2-18CHANGE PRIMARY CONTROL MONITORTo change the control monitor (but not the control camera), enter the one ofthe following com

PRIMARY CONTROL MONITOR2-19Example:The display on the controller shows CAM 1/MON 1.CNTL - CAM 1 MON 1Enter the following command sequence to change th

SECONDARY CONTROL CAMERA2-202.2.4 Secondary Control Camera And Monitor.The secondary camera and monitor are displayed on the second line of thedisplay

SECONDARY CONTROL CAMERA2-21Example:Select camera 2 as the secondary camera.2>CAMThe number 2 shows up on the second line of the controller display

Issue 1, Revision A – July 1997 – added caution to plug programming keyboard intocontroller before power-up of system to ensure proper operation.Issue

SECONDARY CONTROL MONITOR2-22SELECTING A SECONDARY MONITORTo select a secondary monitor, enter one of the following command se-quences.Monitor #>MO

SECONDARY CAMERA/MONITOR2-23CALL UP SECONDARY CAMERA TO SECONDARY MONITORTo switch the video of the secondary camera to the secondary monitor, theseco

SECONDARY CONTROL TO PRIMARY CONTROL2-242.2.5 Switch Secondary Control To Primary Control.To have the secondary camera/monitor combination displayed b

VIDEO SWITCHING2-252.2.6 Call Up Any Camera To Any Monitor.To call up any camera to any monitor without giving up PreShot andVectorScan control of the

VIDEO SWITCHING2-262>MONCNTL - CAM 1 MON 12 2ENTERThe controller sends out a command to switch camera 2 to monitor 2.CLEARCNTL - CAM 1 MON 12CLEAR

PRESHOTS2-272.2.7 PreShotsEach SmartScan unit can store up to 100 PreShots (00-99). The KD6 Z-Series can store up to 64 PreShots (1-64). A list of t

PRESHOTS2-282.2.7.2 Go To PreShotA PreShot call is sent to the control camera unless a secondary controlcamera is selected, then it is sent to the sec

PRESHOTS2-29Example:The controller display shows:CNTL - CAM 1 MON 1(no secondary camera/monitor selected)Send camera one to PreShot 2. Enter one of t

PRESHOTS2-30Note: on some pan and tilt models, the PreShot title and camera IDdisplay positions are programmable. They may not be located in theposi

VECTORSCANS2-312.2.8 VectorScans.Each SmartScan, SmartScan Pro II, SmartScan III series, or KD6 unit canstore up to 10 VectorScans (0-9). A list of t

TERMSThe following terms are used often throughout this manual. Please become familiarwith them before operating and programming a SmartScan system.

VECTORSCANS2-32Enter the 1st PreShot # (1-64) PS#Press Enter EnterEnter a dwell time (0-30 seconds) 0-30Press Enter EnterEnter the next PreShot # (1-6

VECTORSCANS2-332.2.8.2 List VectorScans (Not applicable to KD6 Z-Series)The list displays the VectorScan numbers and their titles. The listingcannot

VECTORSCANS2-34Press 1 to view the next page of the list. 1Press 2 when done viewing the list. 22.2.8.3 List VectorScan Contents (Not applicable to KD

VECTORSCANS2-35SmartScan unit. The VectorScan contents cannot be edited from thislisting.Press 1 to move up one line in the list.Press 2 to move down

VECTORSCANS2-36Enter VectorScan #Press ENTERVSCAN # ENTERExample:The controller display shows:CNTL - CAM 1 MON 1(no secondary camera/monitor selected)

VECTORSCANS2-37PreShot TitleCAM 001 AMONITOR DISPLAYThe SmartScan unit goes to the next PreShot in the list and remainsthere for the specified dwell t

SECTOR ID'S2-382.2.9 Sector ID List (not applicable to KD6 Z-Series)Sector ID titles are added to the video signal of the SmartScan camera whenan

MONITOR SEQUENCING2-392.2.10 Monitor Sequencing (1-32).Monitor sequences only apply to systems with a CATS Video Switcherinstalled. A sequence can be

MONITOR SEQUENCING2-402> ENTER>CNTL - CAM 1 MON 11>ON/OFF 2>DEL 3>PGM1>CNTL - CAM 1 MON 1Run/Stop Seq. - 2To stop the sequence, perf

MONITOR SEQUENCING2-412> ENTERCNTL - CAM 1 MON 11>ON/OFF 2>DEL 3>PGM2CNTL - CAM 1 MON 1Delete Seq. - 2

AUXILIARY CONTROL2-422.2.11 Auxiliary Contact Output Control (ON/OFF)The controller can be used to turn auxiliary devices on or off. The CATSVideo Sw

AUXILIARY CONTROL2-432. Press AUX>CNTL - CAM 1 MON 1Enter Aux. No.Auxiliary #>ENTER>CNTL - CAM 1 MON 11>ON 3>OFF1CNTL - CAM 1 MON 1Aux

AUXILIARY CONTROL2-442. Press AUX>CNTL - CAM 1 MON 1Enter Aux. No.Auxiliary #>ENTER>CNTL - CAM 1 MON 11>ON 3>OFF3CNTL - CAM 1 MON 1Aux

AUXILIARY CONTROL2-451) Call up the address of the AIF-100/CO as the control camera. Theaddress is 2.2>CNTLThe controller display should read:CNTL

MANUAL CONTROL (SMARTSCAN)2-462.2.12 Manual Control of SmartScan.There are two ways to return manual control of a SmartScan Unit to thecontroller duri

FIND HOME (SMARTSCAN)2-472.2.13 Find Home.The Home position is a reference point used by the SmartScan unit to definea starting position for the pan,

FREEZE OR UNFREEZE VIDEO2-482.2.14 Freeze or Unfreeze Video (KD6 UltraDome only)To freeze the camera video scene, perform the following procedure.Pres

TOURS2-492.2.15 Tours (KD6 UltraDome only)The user can program three (3) PTZ tours. Each tour is a maximum of twominutes (120 seconds). When a PTZ t

TOURS2-50Perform the desired pan, tilt, and zoom commands. The maximumprogramming time is two minutes (120 seconds). To end programmingbefore the un

TOURS2-512.2.15.3 Stop TourTo stop a tour, manually control the camera where the tour is running.

iTABLE OF CONTENTSPageSECTION 1. INTRODUCTION ...1-11.1 DESCRIPTION

DIAGNOSTICS2-522.2.16 Joystick Diagnostics.A diagnostics menu can be called up on the controller LCD display to verifythe large joystick on the contro

DIAGNOSTICS2-53Offset shows the values the controller is sending out when the joystick ismoved.P = Pan SettingT = Tilt SettingZ = Zoom SettingActual2&

CAMERA ID DISPLAY2-542.2.17 Camera ID Display on Monitor.The SmartScan units are factory set to add the camera number to the videosignal. The SmartSc

CAMERA ID DISPLAY2-55This display can be enabled (On) or disabled (Off). To enable or disable thedisplay for a SmartScan unit, it must be the control

AZIMUTH/ERROR LOG2-562.2.18 Pan, Tilt, Zoom, and Focus Azimuth Display/Error Log Display.A display showing the azimuth coordinates of the pan and tilt

AZIMUTH/ERROR LOG2-57CAM nnn ETo return to the azimuth display, enter OPT>6>3 again. This commandtoggles between the two displays.Azimuth Displ

2-58Table 2-1. CONTROL COMMANDSCommand(Keystrokes are separated by >)DescriptionOPT>1>1 Select LCD Display LanguageOPT>1>2 Set address

2-59

3-1SECTION 3. PROGRAMMING3.1 PRESHOTSA PreShot is a predefined position (including the pan, tilt, zoom, and focussettings). A PreShot is saved with

iiTABLE OF CONTENTSPage2.2.10 Monitor Sequencing (1-32)...2-392.2.11 Auxiliary Contac

3-2Perform the following steps to program and store “Quick” PreShotsfor the primary control camera using the JPD-101 Controller.a. Adjust the pan, til

3-33.2 PROGRAMMING THE EIGHT FUNCTION KEYS ON THE JPD-101CONTROLLERFunction keys one through eight on the JPD-101 Controller can be programmedto perfo

3-4Option DefinitionsEdit allows the operator to program a function key or edit an existingprogram.Clear deletes the existing programming for the fun

3-5Display DefinitionsKey#1/#1 = Function key #1/Step #1Edit = Create a new step or modify the existing stepExit = Exit the Edit command; returns the

3-65) Select the desired function for the first action by moving the cursor tothe letter of the function and pushing the small joystick up or down.a)

3-7Enter the SmartScan unit number the PreShot is stored in andpress ENTER. The following display appears on the JPD-101.Key#1/#1 PreShotPreShot-n CA

3-8Type the Monitor Number and press ENTER. The followingdisplay appears on the JPD-101.Key#1/#1 Edit ExitCall Cam-n Mon-ne) AuxiliaryTo control an a

3-9Key#1/#1 Edit ExitAux-n Cam-n ONorKey#1/#1 Edit ExitAux-n Cam-n OFFf) W = WaitA wait time can be programmed as one of the actions. The waitfunctio

3-10Key#1/#2 Edit Exit7) Program the desired functions for the remaining actions using theprocedures outlined in paragraphs 3 through 7 above.NOTEIf t

3-113.2.2 Modify an Action Programmed for a Function Key.Any of the actions programmed for a function key can be edited or deletedand actions can be i

iiiTABLE OF CONTENTSPage4.1.2 Enable/Disable Communications. ...4-34.2 INTERCONNECTING CABLING

3-12The text to the right of the Key#n/#n describes the letter the cursor ison.M = ModifyI = Insert (Insert an action above the action the cursor is o

3-133.2.3 Inserting An Action Between Actions For A Function Key.To insert an action between two actions, perform steps one through five inparagraph 3

3-143.2.5 Clearing a Function Key.To clear the programming from a function key, perform the following steps.1. Press PRGM.2. Press 1.3. Select the fun

3-15Below are examples of the displays that have the Exit function.Key #1/#1 Edit ExitCall Cam-n Mon-nThe Exit option in the above display returns th

3-162. Type the monitor number (1-15) you are programming the sequence for andpress the ENTER key on the controller.The following prompt appears on th

3-17The following message is displayed briefly.CNTL-CAM 1 MON 1Program is doneThe controller sends the data to the video switcher and the video switch

3-18This page left blank intentionally.

4-1SECTION 4. SETUP AND INSTALLATION4.1 SETUP PROCEDURESSince the JPD-101 Controller can be used as stand-alone unit or twocontrollers can be linked

4-2Note: Jumper W7 is not used.Figure 4-1. JUMPER SETTINGS4.1.1 Master/Slave.If there is only one JPD-101 Controller installed, it must be configured

4-3Table 4-1. MASTER/SLAVE CONFIGURATIONJPD-101Master SlaveJumper W8 Out In4.1.2 Enable/Disable Communications.If only one controller is used in a sy